Morin's AA-12 profile from the Concealed Fastener Series is one of many profiles within this product line with a common side joint, providing the designer full creative license to mix and match throughout the facade, creating the exact desired effect.
Lengths 5' (1.52m) to 30' (9.14m) standard Shorter and longer lengths available
Deliver panel materials and components in the original, unopened, undamaged packaging with identification labels intact.
Store wall panel materials on dry, firm, and clean surface.
Elevate one end of bundle to allow moisture run-off, cover and ventilate to allow air to circulate and moisture to escape.
Install panels plumb, level, and true-to-line to dimensions and layout indicated on approved shop drawings.
Remove protective film immediately as per Morin's standard directions.
Cutting and fitting of panels shall be neat, square and true. Torch or abrasive cutting is prohibited.
Concealed fastener wall panel
Weather-resistant or rainscreen rear-ventilated application
Galvalume/Zincalume Steel: 18 thru 24 GA Aluminum: 0.050 GA and 0.040 GA Stainless Steel: 20 GA, 22 GA and 24 GA Zinc: 1.2mm, 1.0mm, and 0.8mm Natural Copper: 20oz. and 16 oz.
Standard (Fluropon® PVDF-Kynar500®) Premium Colors MICA (Fluropon Classic®II PVDF) Premium Colors METALLIC (Fluropon Classic®PVDF) Morin Custom Color Matching Services Other Finishes Available
Smooth surface standard; Stucco embossed texture optional. Optional Ribs are also available for additional strength and visual continuity on wider panels.
Optional factory sealant available
Negative pressure clip required. Reference Load Span Charts for further explanation.
Open framing or other various backup wall assemblies (i.e. ext. sheathing, air/water barrier, exterior insulation)
Concealed fastener design.
Common joint design allowing multiple panel integration.
Panels may be installed vertically, horizontally, or in combination.
Bristol, CT, Fontana, CA and DeLand, FL
Air Infiltration: ASTM E283 Water Penetration: ASTM E331 Dynamic Water Penetration: AAMA 501 Structural Performance: ASTM E330 and E1592 Impact Testing-Florida Product Approvals: ASTM E1996/ E1886; TAS204
Copper (Mill Finish) 16 oz. (.0216) = 1.46# psf 20 oz. (.0270) = 1.83# psf
VM Zinc or Rheinzink 0.8 mm (22 ga.) = 1.73# psf 1.0 mm (20 ga.) = 2.16# psf 1.2 mm (18 ga.) = 2.59# psf
Fluropon - 20 solid colors (Low Gloss) (1.0 mil - 2 coat) Fluropon Classic II - 5 mica colors (1.0 mil - 2 coat) Fluropon Classic - 4 metallic colors (1.5 mil- 3 coat) All material has 0.5 mil. Off-White backer
Optional Off White Butyl (Non- Hardening) available
E-5 Directional Pattern; Aztec Stucco Pattern EAST Only
Closure AA-12 Outside Metal 2'-0" long; Closure AA-12 Outside Foam 3'0" long (100 pcs); Closure AA-12 Inside Metal 1'-0" long; Closure AA-12 Inside Foam 100 pcs per ctn (1'-0" long)
1 1/2" DEEP EXTRUSIONS option available
Negative Pressure Clip: Individual Clip, Galvalume: Supply quantity as needed, no full carton requirements; Individual Clip S/S (used on copper and S/S panels): Supply quantity as needed; Continuous Clip, Galvalume: 10'-0" long Formed Trim
12" long: use in place of swedged lap, Install behind panel w/rivet and seal
Mitered Seamed Corners 2'-0"x 2'-0" 90° Minimum 70° (closed) Maximum 135° (open) outside or inside Max. length of leg 6'-0" long Perforated to be cut and bent only - No glue
Folded ends: Available option. Notch and fold both ends of panels (Consult inside sales office)
Swedged ends ( east only): 2" swedged one end (18 ga. N/A) Swedge top of vertical panels ( install L to R ) ; Swedge right end of horiz pnl (install top to bottom)
34 pieces east, 32 pieces south, 30 pieces west. 3 bndls wide on trailer 4 bndls high on trailer
31 1/2"W x 17 1/2"H
3/8" holes x 9/16" oc (40% open) 1/8" holes x 3/16" oc (40% open) 1/8" holes x 7/32" oc (30% open) 1/4" holes x 1/2" oc (23% open) 1/8" holes x 1/4" oc (23% open) 1/8" holes x 3/8" oc (10% open)
# 12 x 1 1/4" Tek 5 n/w Fasten panel to structural steel with one fastener # 12 x 1 1/4" Tek 5 n/w 400 S/S Fasten panel to structural steel with one fastener # 12 x 1" Tek 3 n/w Fasten panel to light ga. steel with one fastener # 12 x 1" Tek 3 n/w 400 S/S Fasten panel to light ga. steel with one fastener # 14 x 1 1/2" type A n/w (no color) Fasten panel to wood with one fastener #44 Pop Rivet 1/8" 400 S/S Fasten trim and splice plates to panels
Limited Finish Warranty 1 to 20 year Available at no charge (check specs for req'd years) Limited Material Warranty 1 to 20 year Available at no charge check specs for req'd years) Limited (Wall) Weather Tight Warranty 1 to 20 year Available for addt'l charge (inspection and shop dwgs review req'd)