Morin Exposed Fastener Series E-36

Morin E-36 Exposed Fastener Series wall and roof panel is one of many profiles within this product line providing architects with a myriad of design opportunities, including horizontal, vertical or diagonal applications and is ideal for new or retrofit projects.

Lengths 5' (1.52m) to 30' (9.14m) standard Shorter and longer lengths available
Deliver panel materials and components in the original, unopened, undamaged packaging with identification labels intact. Store wall panel materials on dry, firm, and clean surface. Elevate one end of bundle to allow moisture run-off, cover and ventilate to allow air to circulate and moisture to escape. Install panels plumb, level, and true-to-line to dimensions and layout indicated on approved shop drawings. Remove protective film immediately as per Morin's standard directions. Cutting and fitting of panels shall be neat, square and true. Torch or abrasive cutting is prohibited.
Exposed fastener wall panel
Weather-resistant or rainscreen rear-ventilated application
1"
25mm
36"
914mm
n/a
Galvalume/Zincalume Painted Steel Options in 18, 20, 22 and 24 GA Aluminum - 0.063, 0.050 and 0.040 GA Stainless Steel - 20, 22 and 24 GA Zinc - 1.2 mm, 1.0mm, 0.8mm Natural Copper- 20 oz. and 16 oz.
Standard (Fluropon® PVDF-Kynar500®) Premium Colors MICA (Fluropon Classic®II PVDF) Premium Colors METALLIC (Fluropon Classic®PVDF) Morin Custom Color Matching Services Other Finishes Available
Smooth surface standard; Stucco embossed texture optional
Field applied as required by design
n/a
Open framing or other various backup wall assemblies (i.e. ext. sheathing, air/water barrier, exterior insulation)
Overlapping side joint design. May be insulated to meet required thermal values. Ideal for new or retrofit projects. All weather installation.
Fontana, CA
Pending Technical Review
West: 44 1/2"
Galvalume AZ-50 & Galvalume Plus AZ-55 24 ga. (.023) = 1.46 # psf 22 ga. (.029) = 1.83# psf 20 ga. (.035) = 2.19# psf 18 ga. (.047) = 2.92# psf
Aluminum (3003 - H14) BARE and PAINTED .032 (20 ga.) = 0.66# psf .040 (18 ga.) = 0.82# psf .050 (16 ga.) = 1.03#psf .063 (14 ga.) = 1.30# psf
Stainless Steel (304-2B) • 24 ga. (.023) = 1.46 # psf • 22 ga. (.029) = 1.84# psf • 20 ga. (.035) = 2.21# psf
Copper (Mill Finish) 16 oz. (.0216) = 1.46# psf 20 oz. (.0270) = 1.83# psf
VM Zinc or Rheinzink 0.8 mm (22 ga.) = 1.73# psf 1.0 mm (20 ga.) = 2.16# psf 1.2 mm (18 ga.) = 2.59# psf
Fluropon - 20 solid colors (Low Gloss) (1.0 mil - 2 coat) Fluropon Classic II - 5 mica colors (1.0 mil - 2 coat) Fluropon Classic - 4 metallic colors (1.5 mil- 3 coat) All material has 0.5 mil. Off-White backer
n/a
E-5 Directional Pattern; Aztec Stucco Pattern EAST Only
Closure E-36 Outside Metal 36" long; Closure E-36 Outside Foam 100 pcs per ctn (300 Linear Feet); Closure E-36 Inside Metal 36" long; Closure E-36 Inside Foam 100 pcs per ctn (300 Linear Feet)
n/a
n/a
n/a
Mitered Seamed Corners 2'-0"x 2'-0" 90° Minimum 70° (closed) Maximum 135° (open) outside or inside Max. length of leg 6'-0" long Perforated to be cut and bent only - No glue
n/a
n/a
3000 pounds maximum bundle weight; 2 bundles wide on trailer (40,000 lbs. max. weight)
300# maximum bundle weight; Number of panels per bundle based on weight
260 squares approximate; based on 22 gauge
3/8" holes x 9/16" oc (40% open) 1/8" holes x 3/16" oc (40% open) 1/8" holes x 7/32" oc (30% open) 1/4" holes x 1/2" oc (23% open) 1/8" holes x 1/4" oc (23% open) 1/8" holes x 3/8" oc (10% open)
# 12 x 1 1/4" Tek 5 with washer and painted; Panel to Structural Steel # 12 x 1 1/4" Tek 5 with washer, painted, stainless steel; Panel to Structural Steel # 12 x 7/8" LapTek, painted*; *use at side laps and trim to panels # 12 x 7/8" LapTek, with washer, painted, stainless steel*; *use at side laps and trim to panels #44 Pop Rivet 1/8" 400 S/S
Limited Finish Warranty 1 to 20 year Available at no charge (check specs for req'd years) Limited Material Warranty 1 to 20 year Available at no charge (check specs for req'd years) Limited (Wall) Weather Tight Warranty 1 to 20 year Available for addt'l charge (inspections and review of shop dwgs. req'd)

Images:


Rending (3D) Image
Profile Image
Project Image 1
Project Image 2
Project Image 3
Project Image 4